RESOURCES

Blade guide.

Most resellers hand you a catalog and let you work out the spec. This page walks through the three questions we ask on every call: what are you cutting, what saw is it going on, and are you running wet or dry. Answer those and the right blade narrows to one or two choices. If you would rather talk it through, call 954-226-0217. The consultation is free whether you buy from us or not.

1. What are you cutting?

Diamond blades do not cut by sharpness. The diamonds do the cutting and the metal bond holding them is built to wear away at a set rate so fresh diamonds keep getting exposed. That is why the material decides the bond:

  • Hard, low-abrasion material (cured concrete with hard aggregate, hard brick, granite) needs a soft bond. The bond wears quickly on purpose so the blade keeps cutting instead of glazing over.
  • Soft, abrasive material (asphalt, green concrete, block, sandstone) needs a hard bond. The material is already wearing the bond fast, so a harder bond holds the diamonds longer and the blade lasts.
  • In between (medium aggregate, pavers, general masonry) takes a medium or general-purpose bond.

The short version: hard material, soft bond. Soft material, hard bond. Get that backwards and the blade either glazes (too hard a bond) or wears out in a day (too soft).

By material

  • Cured concrete – Concrete that has fully set, usually 72 hours and beyond. Pick by aggregate hardness: flint, quartz and river rock call for a softer bond; limestone and softer aggregate take a medium bond. Heavy rebar calls for a blade rated for it. See Wet Blades and Dry Blades.
  • Green concrete – Concrete poured within the last day or two. It is abrasive and the aggregate pulls out easily, so you want a hard bond with undercut protection to stop the sand from eating the core below the segments. Early-entry saws take their own blade type.
  • Asphalt – Very abrasive. A hard bond with undercut protection is the standard choice. Combination asphalt and green concrete blades cover both when the job moves between them.
  • Brick, block and pavers – Clay brick and concrete block are abrasive; a hard to medium bond lasts longest. Hard-fired or engineered brick behaves more like hard stone and wants a softer bond.
  • Stone and tile – Porcelain, granite and natural stone are hard and chip easily. A continuous rim gives the cleanest edge; a turbo rim cuts faster with a slightly rougher edge.
  • Concrete pipe and prestress – Plant-rate cutting on dense, high-strength concrete. These blades are specified for the production line, not for field work.
  • Metal, rebar and ductile iron – A standard concrete blade will not hold up. Use a blade built for steel or a combination blade rated for heavy rebar.

2. What saw are you using?

The saw sets the diameter, the arbor size and the speed. Match the blade to the saw first, then the bond to the material.

  • Angle grinder (4″ to 9″) – dry cutting, grinding, tuck pointing and crack chasing. Also runs cup wheels.
  • Hand-held cut-off saw (12″ to 16″, gas, electric or hydraulic) – the jobsite workhorse for concrete, asphalt, block and pipe. Wet or dry depending on the saw and the blade.
  • Walk-behind flat saw (12″ to 72″, usually wet) – slab, road, runway and floor cutting. Depth is set by the diameter; see the chart below.
  • Early-entry saw – control joints in fresh concrete, cut within hours of the pour. Takes a dedicated early-entry blade with a skid plate.
  • Wall saw (track-mounted, hydraulic or high-frequency) – openings in walls and floors. Blades run at lower RPM and are specified by the saw maker’s arbor and pin pattern.
  • Tile and masonry table saw (6″ to 20″, wet) – clean cuts in tile, stone, brick and block.
  • Core drill – holes for plumbing, electrical and anchors. See Core Bits and the extensions and adaptors in the same section.
  • Concrete chain saw – deep, square-cornered cuts in concrete and block. See Maxcut Diamond Chain.

3. Wet or dry?

  • Wet cutting keeps the blade cool, carries the slurry out of the cut and keeps silica dust out of the air. Wet blades give the longest life and the deepest cuts. A wet blade must never be run dry; the segments can let go.
  • Dry cutting is for hand-held saws and grinders where water is not practical. Dry blades have cooling slots or a laser-welded core for heat. Make shallow passes, back the blade out of the cut every 30 to 45 seconds to let it spin free and cool, and use dust collection or a respirator.
  • Most dry blades can be run wet. Wet blades cannot be run dry. When in doubt, read the rim.

Blade speed and cutting depth

Every blade is built for a speed range. Run it too slow and it will cut slowly and glaze; run it above the maximum and the blade can come apart. The maximum RPM stamped on the blade and the rated speed of your saw always override anything on this page. The figures below are the industry-standard maximums and the operating speeds blades are designed around. Cutting depth is the practical maximum for the diameter, measured with the blade fully lowered through a standard flange.

A note on horsepower and material: a higher-horsepower saw can pull a harder bond and a higher diamond concentration; a lower-horsepower saw wants a softer bond. Harder, less abrasive material cuts best toward the lower end of the operating range; softer, more abrasive material toward the higher end.

Walk-behind wet blades

Blade diameterMax cutting depthRecommended operating RPMMaximum safe RPM
12"3-3/4"2,9004,500
14"4-3/4"2,9003,900
16"5-3/4"2,6003,400
18"6-3/4"2,6003,000
20"7-3/4"2,4502,700
24"9-3/4"1,9502,250
26"10-3/4"1,9502,100
30"11-3/4"1,6501,800
36"14-3/4"1,4001,500
42"17"1,0501,300
48"20"8501,100
54"22-1/2"7751,000
60"25-1/2"625900
72"31-1/2"575750

Dry and hand-held blades

Blade diameterMax cutting depthRecommended operating RPMMaximum safe RPM
4"1"9,07515,000
4-1/2"1-1/4"8,06513,300
5"1-1/2"7,25012,000
7"2-1/2"5,1758,725
8"2-5/8"4,5007,650
10"2-3/4"3,6007,500
12"3-3/4"3,4006,300
14"4-3/4"3,2005,400

Masonry saw blades

Blade diameterMax cutting depthRecommended operating RPMMaximum safe RPM
14"5"2,5503,900
18"7"2,3003,000
20"8"2,3002,900

Tile saw blades

Blade diameterMax cutting depthRecommended operating RPMMaximum safe RPM
6"1-3/4"6,05010,175
7"2-1/4"5,1758,725
8"2-3/4"4,5007,650
9"3-1/4"4,0256,800
10"3-3/4"3,6256,125

Wall saw blades

Blade diameterMax cutting depthRecommended operating RPMMaximum safe RPM
18"6-1/4"1,5003,000
20"7-1/4"1,5002,700
24"9-1/4"1,4502,250
30"12-1/4"1,4001,800
36"15-1/4"1,3001,500
42"18-1/4"9501,300
48"21-1/4"8501,100
54"24-1/4"7001,000
60"27-1/4"625900
72"33-1/4"575750

Figures are industry-standard reference values. Confirm the maximum RPM on the blade itself and in your saw manual before every cut.


Still not sure? Ask us.

Tell us what you are cutting, the saw and the size, and you get a recommendation and a ship date. 32 years in this industry means we have seen the job before. Call 954-226-0217 (24/7) or send the details through the quote form.